Float tube electric motor for predator fishing FLTB MTR
Store Availability
Store availability
BENEFITS
Compact design
Compact, thanks to the design of this engine: 25 x 18 x 19.5 cm.
Compatibility
This motor is compatible with the FLTB-5 V2 (models from 2023) and FLTB-9.
Noise level
A quiet motor for discreet movements when fishing.
Easy assembly / dismantling
Slide it into the base under the float tube then install the safety pin.
Ease of use
The variator is used to precisely adjust the forward and reverse speed.
Ergonomic grip
Offset control unit with magnetic base to fish in optimal comfort
Repair
Go to the SPARE PARTS section.
TECHNICAL INFORMATIONS
SAFETY
Always use your boat and this motor in accordance with the local safety regulations.
When onboard your boat, you must always have a life jacket, in accordance with the local regulations, and a paddle or fins for use in the event of a breakdown.
Only for use by adults.
Do not start the motor out of the water.
Take care when close to the propeller to avoid injury.
INSTALLING THE MOTOR AND THE CONTROL UNIT
This motor is compatible with float tubes and kayaks equipped with the Decathlon fin base. (Reference: 8603033)
Always disconnect the circuit breaker of the control unit before taking any other action.
Insert the motor into the base under the boat, then install the safety pin.
Connect the signal wire between the motor and the control unit.
Check that the wire is properly assembled and watertight.
BATTERY CONNECTOR (not included)
The motor is designed for use with a 12 V battery.
Depending on the battery used, the casting weight will be between 24 and 32 lbs.
We recommend sealed lithium technology batteries, which are lighter and more compact.
You’ll need to adjust the connector based on the type of battery that you’re using.
2 clamp connectors provided. The red wire must be connected to the positive terminal and the black wire to the negative terminal.
CONSUMPTION
Full power forward: 25 Amps, accurate to 23.63A (320w)
Full reverse: 21.2 Amps max (263w)
Average continuous current at half throttle = 5 Amps
Using the motor at half throttle means very high savings on long journeys.
A 12Volt 50Ah battery is therefore an ideal choice for a day’s fishing.
GETTING STARTED
1. Put the magnetic circuit breaker on the control unit. The other end must be attached to the user. Set to 0. The LED must be green.
2. Forward/reverse operation of the motor is controlled using the rotary switch on the control unit.
3. You can use the variator on the control unit to drive the boat forwards or backwards and to adjust the speed.
4. Use fins or paddles to steer your boat.
CHARACTERISTICS, DIMENSIONS AND WEIGHT
MOTOR:
Power in WATTS : 240W
Casting weight in lbs: between 24 and 32 lbs depending on the battery used
Nominal voltage: 12 Volts
Input voltage range: 9–17 Volts
Operating current: 18 Amperes
Watertightness standard: IPX8
Total dimensions: 25 x 18 x 19.5 cm (length x width x height)
PROPELLER:
15 cm (diameter)
CONTROL UNIT:
9 x 5.7 x 4.5 cm (length x width x height)
2.8 cm (diameter of the switch)
Total weight: 3 kg
SPARE PARTS
The following parts are available on this web site or in our stores (to order):
8807567 FLTB MTR CONTROL UNIT
8807590 FLTB MTR CIRCUIT BREAKER
8807595 FLTB MTR PROPELLER
8807597 FLTB MTR PROPELLER SHIELD
COMPOSITION
composition
Motor: 20.0% Copper, 15.0% Butadiene Rubber, 5.0% PCBA, 60.0% Aluminium
Tips for storage and maintenance
DO NOT WASH.
BLEACHING EXCLUDED.
DO NOT TUMBLE DRY.
DO NOT IRON.
DO NOT DRY CLEAN.
Storage tips
Keep the cable connectors and plugs out of the water to avoid damaging them.<br /> Check that the motor is completely dry and clean before storing.
Restrictions on use
Do not start the motor out of the water.
TESTS AND WARRANTY
Parts guarantee
2 years (excluding breakage of the control unit, propeller shield and propeller)