3D hood
We have added a hood with 3D tightening that is easy to adjust in one gesture to the jacket. The fit of the hood is designed to follow your head movements without getting in your way. It is compatible with helmets.
The hood is preformed with a high collar for protecting the face in case of intense cold or strong wind. The flap of the zip closure is micro-perforated to facilitate breathing while protecting the face.
Cuffs
Wide and adjustable sleeves that fit over the gloves to protect you from the snow and keep you dry and warm in case of a snow shower or a fall. Elastane cuffs with a thumb loop providing a perfect seal between the gloves and the jacket.
Ventilation
To stay dry, it is important to wear a waterproof jacket. But you shouldn't end up wet with perspiration.
The vents play an important role in wicking away perspiration.
This is why we have equipped this jacket with two large ventilation zips under the arms (35 cm in size L).
And one quick ventilation zip on the front of the jacket, enabling you to open and close the vent very quickly.
Pockets
2 hand pockets with a waterproof zip.
1 inside chest pocket with watertight zip.
1 outer chest pocket with watertight zip.
1 pocket on the left pocket for your skipass with watertight zip.
2 quick access inside mesh pockets.
Cut
The wide fit, pre-shaped sleeves are there to free movement and enable you to ride in complete freedom.
We have designed this jacket with 2 components. To guarantee good fluidity and freedom of movement, as well as resistance to abrasion.
What should you wear under your skiing jacket?
To keep warm and dry, use the 3-breathable-layers rule: A ski base later and a second layer liner jacket to retain warmth, a third layer ski jacket to protect you from bad weather.
The second layer provides warmth, such as down jackets or fleece sweaters.
The third layer
Protection from the outdoor elements (snow, rain and wind) by preventing them from entering (while still allowing perspiration to escape so that you do not feel "wet inside"). It should therefore ideally be waterproof AND breathable. The third layer can also provide insulation in the case of lined trousers or jackets and thus complement the action of the second layer).
How can I prevent snow from getting in when I fall?
The snow skirt is a protection system at waist level that closes with press studs at the bottom of the ski or snowboard jacket. It prevents snow and draughts from entering when practicing wintersports, especially in the event of a fall. It can be fastened to the trousers using the 3 loops with a press stud.
Water repellency
The water-repellent property of a fabric is its ability to make water run off its surface without absorbing it. This prevents the fabric from becoming waterlogged and remains light, breathable and warm. A fabric is made water-repellent by applying a treatment to its outer surface. This treatment needs to be renewed during the lifetime of the garment (we recommend every 3 washes). All Wedze jackets have received a water-repellent treatment.
Component waterproofing
The resistance of a fabric is measured by the height of a water column in mm that can be supported by the fabric (test based on the ISO 811 standard). The higher the pressure, the more waterproof the fabric. For example, a fabric with a waterproof rating of 15000 mm is therefore resistant to the pressure exerted by a 15000 mm column of water
Breathability of a component
To find out whether a fabric is breathable, we test its evaporative resistance or RET (based on the ISO 11092 standard). The lower the fabric's resistance, the more water vapour generated by physical activity can escape and the higher the fabric's breathability.
For example:
RET < 9 = extremely breathable fabric
9 < RET < 12 = very breathable fabric
12 < RET < 20 = breathable fabric
RET > 20 = little or no breathability.
What is a membrane or coated component?
The coating is akin to a paint applied inside the fabric that makes the component waterproof while remaining breathable. It is often less expensive than a membrane and requires a liner to protect it. The membrane is a kind of very thin plastic film (polyurethane) that makes the component waterproof while remaining breathable. It has the advantage of being more flexible, lighter, more resistant and often more breathable than a coating.
How do we make a garment waterproof?
The waterproofing of the garment is related to its fabric, seam sealing and assembly design.
We then carry out shower tests on our garments.
Waterproofness/Shower test
This garment has been validated in a shower test under 100 L of water / sqm / hour for 3 hours. This test reproduces the conditions of a heavy mountain storm.
How do we make a garment breathable?
In addition to the breathability of the fabrics used, we employ technical solutions (zips, vents, mesh) improving the overall ventilation of our jackets and trousers designed for Freeride skiing. These ventilation systems regulate the temperature inside the garment while also helping to eliminate the perspiration generated by the body during physical activity.
Your product is repairable
This product is repairable.
We commit to repairing your product free of charge for the duration of the warranty. Whatever it is, fixings, seams, zips, etc. This service is offered in your usual store.
If, however, we can’t repair your product (non-repairable production defect), you can exchange it or get a refund.
What is the RECCO® system?
All our Freeride jackets and trousers are equipped with the RECCO® system.
With RECCO® technology, you can be located in the event of an avalanche. Someone who is buried in the snow can be quickly and accurately located by the emergency services using the RECCO® tracker and reflectors. RECCO reflectors are not a substitute for an AVD. The RECCO® technology works as a complementary measure, increasing the chances of being found in time.
Tutorial on how to wash your waterproof garment
We recommend that you follow these guidelines at every wash in order to retain all the technical features of your garment.
Link: https://youtu.be/rh4GLwALgBM
After three washes, restore the water repellent properties with a waterproof spray or wash-in product.
To help you choose the right size
The model on the photo is wearing a size M and measures 175 cm.
Measurements:
Chest measurement: 92 cm
Waist measurement: 66 cm
Hip measurement: 89 cm