Waterproof sailing jacket - wet-weather windproof jacket SAILING 100 navy blue
Store Availability
Store availability
BENEFITS
Compact design
Compact, the jacket folds away into its hood
Water repellent
Especially treated so water slides off the fabric surface.
Resistance to salt water
Materials and zip fastenings resistant to salt water and sea air.
Windproof
Fabric especially coated to reduce the cooling effect of the wind.
Waterproof
Moderate rain for 2 hrs 5,000 mm Schmerber (JIS standard) Pockets not waterproof
Pockets
3 secure pockets, including 1 inner pocket
Breathability
Very breathable coated fabric (RET < 12): reduces condensation
TECHNICAL INFORMATIONS
Waterproofing 1/2
We measure the fabric resistance to water pressure in mm of water column (based on the JIS standard). The higher the water pressure withstood by the fabric, the more waterproof it is.
On our Sailing 100 jacket:
Component is resistant to water pressure of 5,000 mm Schmerber (JIS standard). This equates to the average pressure applied by the water during a rain shower.
The anorak’s waterproofness was tested in a rain shower with 60 litres of water/m²/hour for 2 hours.
Waterproofing 2/2
- High collar
- Injection-moulded plastic to avoid salt oxidation
- Water-repellent components (water runs off the fabric)
- 100% taped seams
- Central opening features a flap with a drainage channel for optimal waterproofing
Hood
The hood does not pack down into the collar, it is attached.
Completely depth and height-adjustable hood.
Visor with a headband to provide a good level of protection and a better hold.
The high neck effectively protects the neck.
Pockets
2 zip pockets on the front of the jacket to put your hands or some items
1 inside pocket on the right side of the chest with a rip-tab closing
NOTE: the pockets are NOT WATERPROOF
Front zip closure
A zip on the entire jacket length with an interior flap protects against the wind and water.
Soft fabric flap on the top of the collar to protect the chin.
Fabric breathability
To find out whether a fabric is breathable, we test its evaporate resistance or RET (ISO 11092 standard). The lower the fabric’s resistance, the more moisture is evaporated, and therefore the higher the fabric’s breathability.
We consider that if:
RET < 9 = highly breathable fabric
9 < RET < 12 = breathable fabric
The RET of the Sailing jacket 100 is 12.
Water-repellent properties information
A fabric is water-repellent when water slides off the surface of the fabric, without seeping in.
Your jacket does not become waterlogged and remains lightweight and breathable. The water-repellent properties are achieved with a treatment applied to the external side of the fabric, but in practice these properties can be altered.
The water-repellent properties can be reactivated by putting the jacket in a dryer for 10 minutes at the lowest temperature.
How to wash your jacket?
To maintain the water repellent properties, infrequent washing is recommended.
Close all zips and flaps, empty all pockets and then turn the garment inside out to wash it. You can wash it on a synthetic cycle at 30°C or 40°C with your usual detergent. Do not use fabric conditioner, which could damage the existing performance of the garment, or bleach. Very important: choose a full rinse cycle or extra rinse.
How to reactivate the jacket’s water repellency
Drying is a crucial phase in reactivating the water repellent treatment.
We recommend that you lay your jacket flat on a clothes rack and leave it out to dry in the open. Caution: never dry your jacket directly on a radiator.
Then put them in the tumble dryer on a short synthetics cycle, i.e., 10 to 15 minutes, before turning it back the right way round. Caution: do not over-dry the garment.
COMPOSITION
composition
Upper part - Main fabric: 100.0% Polyamide; Lower part - Main fabric: 100.0% Polyamide; Main lining: 100.0% Polyester; Sleeve lining: 100.0% Polyester; Coating: 100.0% Polyurethane
Tips for storage and maintenance
MAXIMUM WASHING TEMPERATURE 30°C. NORMAL TREATMENT.
BLEACHING EXCLUDED.
DRYING IN TUMBLE DRYER POSSIBLE. LOW TEMPERATURE, MAXIMUM DRUM EXHAUST TEMPERATURE 60°C.
DO NOT IRON.
DO NOT DRY CLEAN.
TESTS AND WARRANTY
Warranty
2 Years
Ecodesign approach
With ecodesign, we reduce the environmental impact of our products.
Analysing the product's environmental footprint enabled us to identify the most impactful stages of its life cycle. Thanks to this approach, our design teams were able to develop this product while significantly reducing its environmental impact.
Ecodesign actions on this product
-
ProcessDope dyed
Product made from 52% dope dyed yarn
Using this mass-dyeing process enables us to reduce CO2 emissions linked to the production of dyed textiles by at least 17% compared to conventional dyeing.
-
MaterialRecycled polyester
Product made from 17% recycled polyester
Using recycled polyester rather than conventional polyester reduces the CO2 emissions linked to the material by at least 17%.